home *** CD-ROM | disk | FTP | other *** search
- SECTION 13032
-
- SAUNAS
- NOTE ** Finlandia Sauna Products, Inc., precut, prefab, and
- outdoor saunas and sauna accessories.
- NOTE **
- NOTE ** This section is based on the products of Finlandia
- Sauna Products, Inc., which is located at:
- NOTE ** 14010-B S.W. 72nd Avenue
- NOTE ** Portland, OR 97224-0088
- NOTE ** Tel: (503) 684-8289
- NOTE ** Tel: (800) 354-3342
- NOTE ** Fax: (503) 684-1120
- NOTE ** email: finlandiasauna@worldnet.att.net
- NOTE ** Web page: finlandiasauna.com
-
- NOTE ** Finlandia Sauna Products, Inc. provides
- prefabricated (FPF) saunas and precut (FPC) sauna
- packages in a variety of woods; including benches,
- door, heater, heater fence, headrest, backrest,
- trim and base, Super Dek sanitary removable
- flooring, and accessories.
- NOTE **
- NOTE ** SECTION 13032 - SAUNAS, Copyright 1998, The
- Architect's Catalog, Inc.
-
- PART 1 GENERAL
-
- 1.1 SECTION INCLUDES
- NOTE ** Delete items below not required for project.
-
- A. Precut saunas.
-
- B. Custom precut saunas.
-
- C. Prefabricated modular saunas with exclusive locking
- system.
-
- D. Insulated outdoor saunas.
-
- E. Sauna heaters.
-
- F. Sauna accessories.
-
- 1.2 RELATED SECTIONS
- NOTE ** Delete sections below not relevant to this project;
- add others as required.
-
- A. Section 03300 - Cast-In-Place Concrete: Flooring
- substrate.
-
- B. Section 06100 - Rough Carpentry: Framing of walls and
- ceilings.
-
- C. Section 07210 - Building Insulation: Insulation of walls
- and ceilings.
-
- D. Section 09300 - Tile.
-
- E. Section 09650 - Resilient Flooring.
-
- F. Section 15150 - Sanitary Waste and Vent Piping: Floor
- drains.
-
- G. Section 16100 - Wiring Methods: Electrical service
- wiring.
-
- H. Section _____ - __________________________________.
-
- 1.3 SUBMITTALS
-
- A. Submit under provisions of Section 01300.
-
- B. Product Data: Manufacturer's descriptive literature for
- saunas and components specified in this section.
-
- C. Shop Drawings: Plan and elevations of sauna design,
- indicating construction details.
-
- D. Samples: Two samples, minimum size 4 inches wide by 8
- inches long, of specified materials for wood paneling.
-
- E. Manufacturer's printed installation instructions for
- sauna, benches, and accessories.
-
- F. Operation and Maintenance Data: Sauna enclosure, heater,
- and control/monitoring equipment.
-
- G. Warranty documents: Issued and executed by manufacturer.
-
- 1.4 DELIVERY, STORAGE, AND HANDLING
-
- A. Store products of this section in manufacturer's unopened
- packaging until installation.
-
- B. Maintain dry, heated storage area for products of this
- section until installation of products.
-
- 1.5 WARRANTY
-
- A. Manufacturer's Warranty: One-year on room materials and
- workmanship when installed according to manufacturer's
- specifications and wiring information, 5 years on factory
- labor.
-
-
- PART 2 PRODUCTS
-
- 2.1 MANUFACTURERS
-
- A. Acceptable Manufacturer: Finlandia Sauna Products, Inc.,
- 14010-B S.W. 72nd Avenue, Portland, OR 97224-0088; ASD.
- Tel: (503) 684-8289, Tel: (800) 354-3342, Fax: (503) 684-
- 1120; email: finlandiasauna@worldnet.att.net; Web page:
- finlandiasauna.com
-
- B. Substitutions: Not permitted.
-
- C. Provide all saunas and accessories from a single
- manufacturer.
-
- 2.2 MANUFACTURED UNITS
- NOTE ** Retain one of the following paragraphs, completing
- model number designation and size. Custom sizes
- are available for precut saunas; select standard
- sizes seating up to 12 people for precut and prefab
- saunas from manufacturer's literature. Coordinate
- with SECTION INCLUDES Article in PART 1 of this
- section.
- NOTE **
- NOTE ** Precut sauna packages require a framed insulated
- space and a washable floor. Prefab saunas can be
- installed on any level hard-surfaced waterproof
- floor; electrical conduit is sealed within the
- walls, control box (where necessary) is premounted.
- NOTE **
- NOTE ** Prefab 5-sided saunas have a choice of 4 woods for
- interior. Two non-visible exterior walls are of
- ruff sawn mahogany; 3 visible exterior walls are in
- choice of 4 clear woods. Size is 6 feet by 6 feet
- with 7-foot ceiling, full glass door and clear
- glass windows on two sides.
- NOTE **
- NOTE ** Insulated outdoor saunas include a roof package:
- wood plates, prefab rafters, nailers, facing, metal
- flashing, cedar shingles, ridge cap, and nails.
-
- A. Custom Precut Saunas: "FPC _____.".
- 1. Size: ____________________.
-
- B. Prefabricated Modular Saunas: "FPF _____."
- 1. Size: ____________________.
-
- C. Prefabricated 5-Sided Saunas: "FPF66-5S."
-
- D. Insulated Outdoor Saunas.
- 1. Size: ____________________.
-
- 2.3 COMPONENTS
- NOTE ** Retain or edit one of the following paragraphs;
- coordinate with RELATED SECTIONS Article in PART 1
- of this section.
-
- A. Sub-Floor: Specified in Section 03300.
-
- B. Sub-Floor: Specified in Section 09300.
-
- C. Sub-Floor: Specified in Section 09650.
- NOTE ** Retain the following paragraph if specifying precut
- sauna; manufacturer recommends dry Douglas Fir,
- construction grade no. 1 or 2, spaced 16 inches on
- centers, with bottom of ceiling joists 7 feet above
- finished floor. Use pressure-treated plates
- against concrete.
-
- D. Wall and Ceiling Framing: Specified in Section 06100.
- NOTE ** Retain the following paragraph if specifying prefab
- modular saunas or outdoor saunas.
-
- E. Wall and Ceiling Framing: 2 inch by 2 inch Oregon
- Douglas Fir.
- NOTE ** Retain first of the following three paragraphs if
- specifying precut sauna; retain second and third
- paragraphs if specifying prefab or outdoor sauna.
-
- F. Wall and Ceiling Insulation: Specified in Section 07210.
-
- G. Wall and Ceiling Insulation: R-11 (3-1/2 inches)
- fiberglass batt, foil back.
-
- H. Wall and Ceiling Vapor Barrier: Type C Building Foil.
-
- I. Interior Wall and Ceiling Finish: Board paneling of
- nominal 1 inch by 4 inches kiln-dried softwood lumber;
- small V-joint tongue-and-groove.
- NOTE ** Select one of the following four species.
- NOTE **
- NOTE ** California Redwood is the most fire resistant, dry-
- rot resistant, termite resistant, and does not
- warp. Western Red Cedar has the most color
- variation, a refreshing aroma, and is dry-rot
- resistant; as the softest wood, it is least hot to
- sit on or lean against. Alaska Yellow Cedar is an
- exclusive white wood, has a pungent aroma, and is
- silky to the touch. Western Hemlock is excellent
- for people who have wood allergies or are
- chemically sensitive, since it has no aroma and no
- resins.
- 1. Species: California Redwood, clear, 100 percent
- vertical grain.
- 2. Species: Western Red Cedar, clear.
- 3. Species: Alaska Yellow Cedar, clear.
- 4. Species: Western Hemlock, clear.
- 5. Lengths: As required for single board length runs;
- end-to-end joints not permitted except in very large
- rooms.
- NOTE ** Retain one of the following two paragraphs if
- specifying prefab or outdoor saunas. The first is
- standard, the second is an option.
-
- J. Exterior Siding: 11/32 inch ruff-sawn mahogany plywood
- or panolam.
-
- K. Optional Exterior Siding: 1/2 inch by 4 inch tongue-and-
- groove Western Red Cedar.
-
- L. Flooring: "Super Dek" flooring squares for walking areas
- over concrete, tile, or vinyl; removable, washable,
- sanitary, non-skid, synthetic material.
-
- M. Prehung Doors and Frames:
- 1. Door Rails: One-piece vertical grain Oregon Douglas
- Fir, machined for integral stop.
- NOTE ** Retain one of the following subparagraphs.
- Standard door size is 2 feet by 6 feet 8 inches; 3
- foot wide doors are ADA compliant.
- a. Door size: 2 feet wide by 6 feet 8 inches.
- b. Door size: 3 feet wide by 6 feet 8 inches.
- NOTE ** Delete one of the following two subparagraphs.
- c. Door swing, as viewed from outside sauna,
- outswinging: Model FGD-L, hinged left side.
- d. Door swing, as viewed from outside sauna,
- outswinging: Model FGD-R, hinged right side.
- 2. Glass: Hermetically-sealed double glass, tempered.
- NOTE ** Delete all but one of the following three
- subparagraphs. Clear glass is standard in the
- Precut (FPC) and prefab (FPF) saunas. Etched glass
- is an exclusive option, with negative image for
- maximum privacy.
- a. Clear.
- b. Custom designed and etched, negative image.
- c. Custom designed and etched, positive image.
- 3. Casing, Jamb, and Threshold: Vertical grain Redwood,
- S4S, maximum 11 percent moisture content, jamb
- machined for integral stop.
- 4. Hinges: Three 4-inch by 4-inch butts.
- 5. Ball Catch: Ives MP347B3.
- 6. Door Pulls: Two wood pulls 080 each door.
- NOTE ** If a fire sprinkler is required at the sauna, the
- head should be set at 275 degrees F (135 degrees C)
- or higher and should not be located over the sauna
- heater. It will also be necessary to ascertain the
- elevation above sea level for the sauna when
- ordering.
-
- N. Sauna Heaters: Three-wall pressed metal construction,
- stainless steel heating elements, large rock capacity,
- direct rock contact with heating elements, free air flow;
- UL tested and listed.
- NOTE ** Select heater type and model from the five
- subparagraphs below.
- NOTE **
- NOTE ** Insert 30, 45, 60, or 80 after Model FLB below for
- 3,000 (12.5 amps), 4,500 (18.8 amps), 6,000 (25
- amps), or 8,000 (33.3 amps) watts, respectively.
- 3,000 watts is recommended for 84-130 cubic foot
- (2.379-3.682 cubic m) sauna, 4,500 for 100-210
- cubic feet (2.832-5.947 cubic m), 6,000 for 170-300
- cubic feet (4.814-8.498 cubic m), and 8,000 for 250-
- 425 cubic feet (7.080-12.036 cubic m).
- 1. Wall mounted type, single phase; Model FLB____.
- a. Size: 16 inches (406 mm) wide, 11 inches (279
- mm) deep, 24 inches (610 mm) high.
- b. Construction: Stainless steel interior and top,
- baked enamel exterior.
- NOTE ** Delete subparagraph above or below.
- c. Construction: Stainless steel interior and top,
- stainless steel exterior.
- d. Controls: Built-in (60 minute timer,
- thermostat), 8-hour programmable time clock.
- NOTE ** Delete subparagraph above or below.
- e. Controls, Front Mounted: Built-in (60 minute
- timer, thermostat).
- NOTE ** Insert 30, 45, 60, or 80 after Model FIN below for
- 3,000 (12.5 amps), 4,500 (18.8 amps), 6,000 (25
- amps), or 8,000 (33.3 amps) watts, respectively.
- 3,000 watts is recommended for 84-130 cubic foot
- (2.379-3.682 cubic m) sauna, 4,500 for 100-210
- cubic feet (2.832-5.947 cubic m), 6,000 for 170-300
- cubic feet (4.814-8.498 cubic m), and 8,000 for 250-
- 425 cubic feet (7.080-12.036 cubic m).
- 2. Wall mounted type, single phase; Model FIN____.
- a. Size: 16 inches (406 mm) wide, 11 inches (279
- mm) deep, 24 inches (610 mm) high.
- b. Construction: Stainless steel interior and top,
- baked enamel exterior.
- NOTE ** Delete subparagraph above or below.
- c. Construction: Stainless steel interior and top,
- stainless steel exterior.
- d. Controls: Wall mounted; include thermostat, 60-
- minute timer, light switch, and indicator light.
- NOTE ** Include the following subparagraph when specifying
- FIN80. Otherwise, delete.
- e. Contactor: Model FL402; 6 inches (152 mm) wide,
- 8 inches (203 mm) high, 4 inches 102 mm) deep.
- NOTE ** Insert 30-3, 45-3, 60-3, or 80-3 after Model FIN
- below for 3,000 (8.3 amps), 4,500 (12.5 amps),
- 6,000 (16.7 amps), or 8,000 (22.2 amps) watts,
- respectively. 3,000 watts is recommended for 84-
- 130 cubic foot (2.379-3.682 cubic m) sauna, 4,500
- for 100-210 cubic feet (2.832-5.947 cubic m), 6,000
- for 170-300 cubic feet (4.814-8.498 cubic m), and
- 8,000 for 250-425 cubic feet (7.080-12.036 cubic
- m).
- 3. Wall mounted type, three phase; Model FIN_______.
- a. Size: 16 inches (406 mm) wide, 11 inches (279
- mm) deep, 24 inches (610 mm) high.
- b. Construction: Stainless steel interior and top,
- baked enamel exterior.
- NOTE ** Delete subparagraph above or below.
- c. Construction: Stainless steel interior and top,
- stainless steel exterior.
- d. Controls: Wall mounted; include thermostat, 60-
- minute timer, light switch, and indicator light.
- e. Contactor: Model FL303; 6 inches (152 mm) wide,
- 8 inches (203 mm) high, 4 inches 102 mm) deep.
- NOTE ** Insert 90, 105, 120, or 150 after Model FLC below
- for 9,000 (37.5 amps), 10,500 (43.8 amps), 12,000
- (50 amps), or 15,000 (62.5 amps) watts,
- respectively. 9,000 watts is recommended for 300-
- 525 cubic foot (8.496-14.868 cubic m) sauna, 10,500
- for 390-600 cubic feet (11.045-16.992 cubic m),
- 12,000 for 440-750 cubic feet (12.461-21.240 cubic
- m), and 15,000 for 560-1,050 cubic feet (15.859-
- 29.736 cubic m).
- 4. Floor model type, single phase; Model FLC_____.
- a. Size: 17 inches (432 mm) wide, 20 inches (508
- mm) deep, 26 inches (660 mm) high.
- b. Construction: Deluxe stainless steel interior
- and exterior.
- c. Controls: Wall mounted; include thermostat, 60-
- minute timer, light switch, and indicator light.
- d. Contactor: Model FL404; 8 inches (203 mm) wide,
- 12 inches (305 mm) high, 4 inches 102 mm) deep.
- NOTE ** Insert 90-3, 105-3, 120-3, or 150-3 after Model FLC
- below for 9,000 (25 amps), 10,500 (29.2 amps),
- 12,000 (33.3 amps), or 15,000 (41.7 amps) watts,
- respectively. 9,000 watts is recommended for 300-
- 525 cubic foot (8.496-14.868 cubic m) sauna, 10,500
- for 390-600 cubic feet (11.045-16.992 cubic m),
- 12,000 for 440-750 cubic feet (12.461-21.240 cubic
- m), and 15,000 for 560-1,050 cubic feet (15.859-
- 29.736 cubic m).
- 5. Floor model type, three phase; Model FLC_______.
- a. Size: 17 inches (432 mm) wide, 20 inches (508
- mm) deep, 26 inches (660 mm) high.
- b. Construction: Deluxe stainless steel interior
- and exterior.
- c. Controls: Wall mounted; include thermostat, 60-
- minute timer, light switch, and indicator light.
- d. Contactor: Model FL503; 8 inches (203 mm) wide,
- 12 inches (305 mm) high, 4 inches 102 mm) deep.
-
- O. Heater Fence: S4S, kiln-dried clear vertical grain, 1 by
- 2 (3/4 inch by 1-5/8 inches) and 2 by 2 (1-5/8 inches by
- 1-5/8 inches).
-
- P. Benches: S4S, kiln-dried clear vertical grain, 2 by 2 (1-
- 5/8 inches by 1-5/8 inches) tops with 1/2 inch nominal
- spacing; eased edges to eliminate sharp angles.
- 1. Facings: 2 by 4 (1-5/8 inches by 3-1/2 inches) of
- same material as tops; eased edges.
- 2. Trim: Wood species to match room paneling.
-
- Q. Fasteners: Galvanized, applied from bottom to eliminate
- exposed metal; exposed nails countersunk and filled.
-
- R. Vents: 4 inches by 10 inches.
- NOTE ** Include the following two subparagraphs only for
- prefab saunas.
- 1. Lower: Neatly cut into room base.
- 2. Upper: Neatly cut into upper wall.
- NOTE ** Include the following two subparagraphs only for
- precut saunas.
- 3. Lower: Provided for lower wall location.
- 4. Upper: Provided for upper wall location.
-
- S. Light: Vapor-proof, wall-mounted, Progress P5511, satin
- finish cast aluminum, 75 watts.
-
- 2.4 ACCESSORIES
-
- A. Standard Accessories:
- 1. 100N or B; Wood bucket, 1 gallon.
- 2. 100L; Plastic bucket liner.
- 3. 106/40; Wood dipper, 16 inches.
- 4. 079; Tapered headrest.
- 5. 3444; Redwood thermometer.
- 6. PBS; Plexiglass bathing sign.
- 7. P5511; Vapor-proof wall light.
- 8. SD12; Interlocking Super Dek flooring, 12 inches
- square.
- NOTE ** Include the following optional accessories as
- required for the project.
-
- B. Optional Accessories:
- 1. 442F; Cedar towel hanger.
- 2. 5499; Chrome/glass thermometer/hygrometer, 7-inch
- diameter.
- 3. 5498; Chrome/glass thermometer/hygrometer, 5-inch
- diameter.
- 4. 5355; Chrome/glass thermometer, 4-inch diameter.
- 5. 4355; Chrome/glass hygrometer, 4-inch diameter.
- 6. 293A; Wood thermometer/hygrometer.
- 7. 215K; Birch bark sauna sign, 3-1/2 inches by 10
- inches.
- 8. 210K; Sauna sand timer.
- 9. 490-128; Set of two brushes.
- 10. 101N; Wood bucket, 1.84 gallons.
- 11. 3433; Pine "Sauna" door handle.
- 12. 3434; Plain door handle.
- 13. 120; Door handle with towel hook.
- 14. 3465; Light copper bucket.
- 15. 3455; Light copper dipper.
- 16. 106/50; Wood dipper, 19 inches.
- 17. 108N; Wood pail, 2 gallons.
-
-
- PART 3 EXECUTION
-
- 3.1 EXAMINATION
-
- A. Verify that utility services are of correct type and in
- correct locations.
-
- B. Verify that construction activities affecting work of
- this section are correct and complete.
-
- C. Examine conditions under which work of this section is to
- be performed.
- 1. Submit written notification if such conditions are
- unacceptable.
- 2. Transmit two copies of installer's report to
- Architect within 24 hours of receipt.
- 3. Beginning work of this section before unacceptable
- conditions have been corrected is prohibited.
- 4. Beginning construction activities of this section
- indicates installer's acceptance of conditions.
-
- 3.2 INSTALLATION
-
- A. Install saunas and accessories in accordance with shop
- drawings and manufacturer's printed installation
- instructions.
-
- B. Connection of heater, lighting, and control/monitoring
- equipment, to electrical service is specified in Section
- 16100.
-
- 3.3 CLEANING
-
- A. Clean soiled surfaces in accordance with manufacturer's
- instructions.
-
- 3.4 PROTECTION OF INSTALLED PRODUCTS
-
- A. Protect sauna and components from damage to finishes and
- operation until Substantial Completion.
-
-
- END OF SECTION
-